The materials used in this study are 300 g of cement, 100 g of mineral powder [28], 100 g of fly ash, 1 g of concrete ing agent, and 10 g of latex powder. The L16 (44) orthogonal table has ...
The performance including strength, chloride ion penetration resistance, sulfate corrosion resistance, anti-permeability, and frost resistance grade of such concrete with nano-modified fly ash was ...
Strategies to Deal with Fly Ash Concreting in Cold Weather There are two general strategies to use to ensure good performance of fly-ash concrete in cold weather: one is to adjust the …
Powder and Fly Ash as a Partial Replacement of Cement . Irshad Ali . Assistant Professor, Department of Civil Engineering, IFTM University, ... ASR can be prevented or reduced by adding mineral admixtures in the concrete mixture, common mineral admixtures used to minimize ASR are pulverized fuel ash (PFA), silica fume(SF) and metakaolin(MK).A ...
The effect slag powder on strength development of alkali-activated recycled cement paste was investigated. The results show that alkali-activated recycled cement paste has low cementing strengths ...
The basic components of concrete are water, coarse and fine aggregates, and cement. Of these components, is well known that the production of cement is the most environmentally impactful (Nguyen et al., 2018).The production of one ton of cement releases nearly one ton of carbon dioxide (CO 2) into our atmosphere, causing negative impacts on our …
The experimental results indicate that the composite addition of fly ash and slag powder in self-compacting concrete, while compatible with up to 6% micro-steel fibers, leads to a decrease in concrete workability and an increase in cohesiveness due to the addition of micro-steel fibers. ... comprising a mixture of the two mineral admixtures ...
Studies have shown that concrete slump decreases with the addition of pumicite powder [44]. In a study conducted by Kabay et al. [45], it was observed that using pumicite powder, fly ash, and ...
The main quality indicators of fly ash are: fineness, loss on ignition, SO3 content, fCaO content, water demand ratio, water content. The fly ash that can be used for concrete and mortar is divided into grades I, II and III …
Fly ash is typically used as a partial replacement for cement. 3. Pre-test the fly ash: Before using fly ash in a large-scale mortar batch, conduct small-scale tests to assess its impact on the mortar properties. This will help you understand the effects of fly ash on workability, setting time, strength development, and other relevant factors ...
In this article, the Bituminous concrete 16 is taken as the basic material, the limestone mineral powder mixing amount is respectively 5%, 6%, 7%, and simultaneously the fly ash was taken to ...
Because fly ash has different properties than cement, it should be utilized as a mineral admixture rather than as cement, and therefore should never be used as a cement …
A large number of studies have shown that [5][6][7][8], appropriate amount of fly ash and slag powder can obviously improve the cracking sensitivity of concrete, double fly ash and slag powder ...
To study the effect of fly ash, mineral powder, and silica fume on the working performance and mechanical properties of C70 high-performance concrete by adding the same amount of fly ash, granulated blast furnace slag powder, and silica fume as a composite admixture to replace the amount of cement. Influencing the law, at the same time, the optimal dosage ratio of various …
This paper investigates the influence of mineral admixtures fly ash (FA) and ground-granulated blast-furnace slag (GGBS), the byproducts of industry, on chloride ions migration and corrosion ...
Comparing with 20% precursor replacement, the 15% replaced GP or class F Fly ash can increase the reacted geopolymer phases as shown in gel pore increases and strength …
The data on the compressive strength of concrete after fly ash and rice husk ash had been added in percentage increments of 0%, 10%, 20%, 30%, 40%, 50% and 0%, 5%, 7.5%, 10%, 12.5%, 15% ...
1. Introduction. Coating technologies are an effective means of protecting concrete structures from chemical attack and rebar corrosion. Inorganic coatings in particular have been widely applied as anticorrosive and decorative materials for concrete and steel structures [1,2,3,4].These materials show a high long-term durability even under acid and alkali attack …